hrcak mascot   Srce   HID

Izvorni znanstveni članak

Effect of the cutting parameters on cutting forces in high speed face milling

Ahmet Čekić ; University of Sarajevo, Faculty of Mechanical Engineering, Vilsonovo šetalište 9, 71000 Sarajevo, B&H
Đerzija Begić-Hajdarević ; University of Sarajevo, Faculty of Mechanical Engineering, Vilsonovo šetalište 9, 71000 Sarajevo, B&H
Malik Kulenović ; University of Sarajevo, Faculty of Mechanical Engineering, Vilsonovo šetalište 9, 71000 Sarajevo, B&H

Puni tekst: engleski, pdf (1 MB) str. 775-780 preuzimanja: 680* citiraj
APA 6th Edition
Čekić, A., Begić-Hajdarević, Đ. i Kulenović, M. (2013). Effect of the cutting parameters on cutting forces in high speed face milling. Tehnički vjesnik, 20 (5), 775-780. Preuzeto s https://hrcak.srce.hr/109784
MLA 8th Edition
Čekić, Ahmet, et al. "Effect of the cutting parameters on cutting forces in high speed face milling." Tehnički vjesnik, vol. 20, br. 5, 2013, str. 775-780. https://hrcak.srce.hr/109784. Citirano 02.03.2021.
Chicago 17th Edition
Čekić, Ahmet, Đerzija Begić-Hajdarević i Malik Kulenović. "Effect of the cutting parameters on cutting forces in high speed face milling." Tehnički vjesnik 20, br. 5 (2013): 775-780. https://hrcak.srce.hr/109784
Harvard
Čekić, A., Begić-Hajdarević, Đ., i Kulenović, M. (2013). 'Effect of the cutting parameters on cutting forces in high speed face milling', Tehnički vjesnik, 20(5), str. 775-780. Preuzeto s: https://hrcak.srce.hr/109784 (Datum pristupa: 02.03.2021.)
Vancouver
Čekić A, Begić-Hajdarević Đ, Kulenović M. Effect of the cutting parameters on cutting forces in high speed face milling. Tehnički vjesnik [Internet]. 2013 [pristupljeno 02.03.2021.];20(5):775-780. Dostupno na: https://hrcak.srce.hr/109784
IEEE
A. Čekić, Đ. Begić-Hajdarević i M. Kulenović, "Effect of the cutting parameters on cutting forces in high speed face milling", Tehnički vjesnik, vol.20, br. 5, str. 775-780, 2013. [Online]. Dostupno na: https://hrcak.srce.hr/109784. [Citirano: 02.03.2021.]
Puni tekst: hrvatski, pdf (1 MB) str. 775-780 preuzimanja: 391* citiraj
APA 6th Edition
Čekić, A., Begić-Hajdarević, Đ. i Kulenović, M. (2013). Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju. Tehnički vjesnik, 20 (5), 775-780. Preuzeto s https://hrcak.srce.hr/109784
MLA 8th Edition
Čekić, Ahmet, et al. "Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju." Tehnički vjesnik, vol. 20, br. 5, 2013, str. 775-780. https://hrcak.srce.hr/109784. Citirano 02.03.2021.
Chicago 17th Edition
Čekić, Ahmet, Đerzija Begić-Hajdarević i Malik Kulenović. "Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju." Tehnički vjesnik 20, br. 5 (2013): 775-780. https://hrcak.srce.hr/109784
Harvard
Čekić, A., Begić-Hajdarević, Đ., i Kulenović, M. (2013). 'Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju', Tehnički vjesnik, 20(5), str. 775-780. Preuzeto s: https://hrcak.srce.hr/109784 (Datum pristupa: 02.03.2021.)
Vancouver
Čekić A, Begić-Hajdarević Đ, Kulenović M. Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju. Tehnički vjesnik [Internet]. 2013 [pristupljeno 02.03.2021.];20(5):775-780. Dostupno na: https://hrcak.srce.hr/109784
IEEE
A. Čekić, Đ. Begić-Hajdarević i M. Kulenović, "Utjecaj parametara obrade na sile rezanja pri visokobrzinskom čeonom glodanju", Tehnički vjesnik, vol.20, br. 5, str. 775-780, 2013. [Online]. Dostupno na: https://hrcak.srce.hr/109784. [Citirano: 02.03.2021.]

Sažetak
Machining system VBS was constructed and built at the Faculty of Mechanical Engineering in Sarajevo, for investigations of the phenomena in high speed milling. Since the requests for high speeds and accelerations of the main spindles and the transmitters for the feed motions require specific design and mechatronic solutions, this paper presents the selection of optimal design variety of components integrated in machining system VBS. The investigation of the effect of the cutting parameters on the cutting forces during high speed face milling (range of cutting speed from 750 m/min to 3000 m/min) was conducted on the machining system VBS. Investigations were carried out on hardened alloy steel EN 10083-3 (41Cr4). The results show that cutting force FR decreases by increasing cutting speed. Also the investigations show that the feed per tooth has significant effect upon the values of cutting forces. This paper further presents the mathematical model for calculating cutting force in high speed cutting. Experimental results are compared with calculation results.

Ključne riječi
cutting forces; feed per tooth; machining system; mathematical model; ultra high cutting speed

Hrčak ID: 109784

URI
https://hrcak.srce.hr/109784

[hrvatski]

Posjeta: 1.562 *