hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20160726112308

Magnetic Bearing Control System based on PI and PID Controllers

Miroslav Puskaric ; University of Rijeka, Center for Advanced Computing and Modelling, Radmile Matejcic 2, 51000 Rijeka, Croatia
Zlatan Car   ORCID icon orcid.org/0000-0003-2817-9252 ; University of Rijeka, Faculty of Engineering, Department of Automation and Electronics, Vukovarska 58, 51000 Rijeka, Croatia
Neven Bulic   ORCID icon orcid.org/0000-0001-8957-020X ; University of Rijeka, Faculty of Engineering, Department of Automation and Electronics, Vukovarska 58, 51000 Rijeka, Croatia

Puni tekst: engleski, pdf (2 MB) str. 136-140 preuzimanja: 973* citiraj
APA 6th Edition
Puskaric, M., Car, Z. i Bulic, N. (2018). Magnetic Bearing Control System based on PI and PID Controllers. Tehnički vjesnik, 25 (1), 136-140. https://doi.org/10.17559/TV-20160726112308
MLA 8th Edition
Puskaric, Miroslav, et al. "Magnetic Bearing Control System based on PI and PID Controllers." Tehnički vjesnik, vol. 25, br. 1, 2018, str. 136-140. https://doi.org/10.17559/TV-20160726112308. Citirano 12.05.2021.
Chicago 17th Edition
Puskaric, Miroslav, Zlatan Car i Neven Bulic. "Magnetic Bearing Control System based on PI and PID Controllers." Tehnički vjesnik 25, br. 1 (2018): 136-140. https://doi.org/10.17559/TV-20160726112308
Harvard
Puskaric, M., Car, Z., i Bulic, N. (2018). 'Magnetic Bearing Control System based on PI and PID Controllers', Tehnički vjesnik, 25(1), str. 136-140. https://doi.org/10.17559/TV-20160726112308
Vancouver
Puskaric M, Car Z, Bulic N. Magnetic Bearing Control System based on PI and PID Controllers. Tehnički vjesnik [Internet]. 2018 [pristupljeno 12.05.2021.];25(1):136-140. https://doi.org/10.17559/TV-20160726112308
IEEE
M. Puskaric, Z. Car i N. Bulic, "Magnetic Bearing Control System based on PI and PID Controllers", Tehnički vjesnik, vol.25, br. 1, str. 136-140, 2018. [Online]. https://doi.org/10.17559/TV-20160726112308

Sažetak
This paper describes the implementation of magnetic bearings and their active control system. The working principle of the special combined axial and radial magnetic bearings and their implementation is explained. The overall laboratory system consists of two magnetic bearings with their housings, the suspended shaft and control system with sensors and power electronics. Sensor electronics are used to measure the position of the shaft within a bearing and to determine the appropriate bearing current with outer position control loops and nested current control loops. The motor control board featuring the TMS320F28335 DSP and LDC1000 proximity sensors is used for control and power electronics. In order to implement the control system the X2C tool is used. This is an open source model based development and code generation tool embedded in the Scilab/Xcos environment. The sensor data acquisition time is optimized to increase the speed of the control system.

Ključne riječi
digital signal processor; magnetic bearing; proximity sensor; regulation

Hrčak ID: 193607

URI
https://hrcak.srce.hr/193607

Posjeta: 1.347 *