hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.30765/er.39.1.12

Synthesis of Ti-Zr alloy by powder metallurgy

Ljerka Slokar   ORCID icon orcid.org/0000-0002-3205-3372 ; Faculty of Metallurgy, University of Zagreb
Anita Štrkalj   ORCID icon orcid.org/0000-0002-7117-4687 ; Faculty of Metallurgy, University of Zagreb
Zoran Glavaš   ORCID icon orcid.org/0000-0003-4116-3255 ; Faculty of Metallurgy, University of Zagreb

Puni tekst: engleski, pdf (713 KB) str. 115-123 preuzimanja: 162* citiraj
APA 6th Edition
Slokar, Lj., Štrkalj, A. i Glavaš, Z. (2019). Synthesis of Ti-Zr alloy by powder metallurgy. Engineering Review, 39 (1), 115-123. https://doi.org/10.30765/er.39.1.12
MLA 8th Edition
Slokar, Ljerka, et al. "Synthesis of Ti-Zr alloy by powder metallurgy." Engineering Review, vol. 39, br. 1, 2019, str. 115-123. https://doi.org/10.30765/er.39.1.12. Citirano 05.04.2020.
Chicago 17th Edition
Slokar, Ljerka, Anita Štrkalj i Zoran Glavaš. "Synthesis of Ti-Zr alloy by powder metallurgy." Engineering Review 39, br. 1 (2019): 115-123. https://doi.org/10.30765/er.39.1.12
Harvard
Slokar, Lj., Štrkalj, A., i Glavaš, Z. (2019). 'Synthesis of Ti-Zr alloy by powder metallurgy', Engineering Review, 39(1), str. 115-123. https://doi.org/10.30765/er.39.1.12
Vancouver
Slokar Lj, Štrkalj A, Glavaš Z. Synthesis of Ti-Zr alloy by powder metallurgy. Engineering Review [Internet]. 2019 [pristupljeno 05.04.2020.];39(1):115-123. https://doi.org/10.30765/er.39.1.12
IEEE
Lj. Slokar, A. Štrkalj i Z. Glavaš, "Synthesis of Ti-Zr alloy by powder metallurgy", Engineering Review, vol.39, br. 1, str. 115-123, 2019. [Online]. https://doi.org/10.30765/er.39.1.12

Sažetak
Due to good properties, which meet the requirements for use as biomaterials, titanium and titanium alloys have been increasingly used as dental implants. Until recently, dental titanium alloys were produced by casting. Since this process does not meet the terms of economy and efficiency, the production of titanium implants by powder metallurgy are very promising. Therefore, in this work titanium alloy with addition of 10 at. % zirconium is prepared by powder metallurgy with the goal of obtaining the best producing conditions, which would result in the titanium alloy of the adequate properties for use as dental implants. High values of green densities were achieved even only by uniaxial pressing. Further, sintering temperature of 1673 K resulted in the alloy of the highest sintered density and microhardness. The results of this investigation revealed the processing parameters applicable for the production of titanium-zirconium dental implants by powder metallurgy.

Ključne riječi
titanium alloys; dental implants; powder metallurgy; porosity; density; microhardness

Hrčak ID: 215370

URI
https://hrcak.srce.hr/215370

Posjeta: 297 *