hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20180203185742

Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze

Savas Evran ; Department of Machine and Metal Technologies, Vocational School of Canakkale Technical Sciences, Canakkale Onsekiz Mart University, 17020 Canakkale, Turkey
Bilcen Mutlu ; Department of Mechanical Engineering, Faculty of Technology, Marmara University, 34722 Kadıköy - İstanbul, Turkey
Mustafa Kurt ; Department of Mechanical Engineering, Faculty of Technology, Marmara University, 34722 Kadıköy - İstanbul, Turkey

Puni tekst: engleski, pdf (3 MB) str. 1228-1233 preuzimanja: 102* citiraj
APA 6th Edition
Evran, S., Mutlu, B. i Kurt, M. (2019). Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze. Tehnički vjesnik, 26 (5), 1228-1233. https://doi.org/10.17559/TV-20180203185742
MLA 8th Edition
Evran, Savas, et al. "Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze." Tehnički vjesnik, vol. 26, br. 5, 2019, str. 1228-1233. https://doi.org/10.17559/TV-20180203185742. Citirano 15.11.2019.
Chicago 17th Edition
Evran, Savas, Bilcen Mutlu i Mustafa Kurt. "Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze." Tehnički vjesnik 26, br. 5 (2019): 1228-1233. https://doi.org/10.17559/TV-20180203185742
Harvard
Evran, S., Mutlu, B., i Kurt, M. (2019). 'Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze', Tehnički vjesnik, 26(5), str. 1228-1233. https://doi.org/10.17559/TV-20180203185742
Vancouver
Evran S, Mutlu B, Kurt M. Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze. Tehnički vjesnik [Internet]. 2019 [pristupljeno 15.11.2019.];26(5):1228-1233. https://doi.org/10.17559/TV-20180203185742
IEEE
S. Evran, B. Mutlu i M. Kurt, "Cutting Rate and Surface Characteristic Analysis in CNC Wire Electrical Discharge Machining of Aluminium Bronze", Tehnički vjesnik, vol.26, br. 5, str. 1228-1233, 2019. [Online]. https://doi.org/10.17559/TV-20180203185742

Sažetak
In this study, cutting rate and surface characteristic analysis in wire electrical discharge machining of aluminium bronze were investigated. Cutting rate analyses were performed according to Taguchi L18 (2^1×3^2) orthogonal array. Machining parameters such as wire type, duration between two pulses (BT) and pulse time (AT) were used as control factors. Raw data obtained for cutting rate were converted to S/N ratio values. Optimum levels of the machining parameters for cutting rate were determined using analysis of signal-to-noise (S/N) ratio. Significant machining parameters and their percentage contributions on results were obtained using Analysis of Variance (ANOVA). Regression analysis was performed to model the relationship between cutting rate and machining parameters. Analyses of surfaces machined of workpiece using both two wires for minimum and maximum cutting rate were observed using scanning electron microscope (SEM) and surface roughness device.

Ključne riječi
cutting rate; Scanning Electron Microscope (SEM); surface finish; Wire Electrical Discharge Machining (WEDM)

Hrčak ID: 226003

URI
https://hrcak.srce.hr/226003

Posjeta: 169 *