hrcak mascot   Srce   HID

Prethodno priopćenje

Investigation of the stress-strain state of balls under deformation in a closed die

M. Abishkenov   ORCID icon orcid.org/0000-0002-7995-7651 ; Karaganda state industrial university, Temirtau, Kazakhstan
Zh. Ashkeyev ; Karaganda state industrial university, Temirtau, Kazakhstan
S. Mashekov
G. Akhmetova ; Karaganda state industrial university, Temirtau, Kazakhstan
I. Volokitina ; Karaganda state industrial university, Temirtau, Kazakhstan

Puni tekst: engleski, pdf (1 MB) str. 559-562 preuzimanja: 32* citiraj
APA 6th Edition
Abishkenov, M., Ashkeyev, Z., Mashekov, S., Akhmetova, G. i Volokitina, I. (2020). Investigation of the stress-strain state of balls under deformation in a closed die. Metalurgija, 59 (4), 559-562. Preuzeto s https://hrcak.srce.hr/241218
MLA 8th Edition
Abishkenov, M., et al. "Investigation of the stress-strain state of balls under deformation in a closed die." Metalurgija, vol. 59, br. 4, 2020, str. 559-562. https://hrcak.srce.hr/241218. Citirano 29.09.2020.
Chicago 17th Edition
Abishkenov, M., Zh. Ashkeyev, S. Mashekov, G. Akhmetova i I. Volokitina. "Investigation of the stress-strain state of balls under deformation in a closed die." Metalurgija 59, br. 4 (2020): 559-562. https://hrcak.srce.hr/241218
Harvard
Abishkenov, M., et al. (2020). 'Investigation of the stress-strain state of balls under deformation in a closed die', Metalurgija, 59(4), str. 559-562. Preuzeto s: https://hrcak.srce.hr/241218 (Datum pristupa: 29.09.2020.)
Vancouver
Abishkenov M, Ashkeyev Z, Mashekov S, Akhmetova G, Volokitina I. Investigation of the stress-strain state of balls under deformation in a closed die. Metalurgija [Internet]. 2020 [pristupljeno 29.09.2020.];59(4):559-562. Dostupno na: https://hrcak.srce.hr/241218
IEEE
M. Abishkenov, Z. Ashkeyev, S. Mashekov, G. Akhmetova i I. Volokitina, "Investigation of the stress-strain state of balls under deformation in a closed die", Metalurgija, vol.59, br. 4, str. 559-562, 2020. [Online]. Dostupno na: https://hrcak.srce.hr/241218. [Citirano: 29.09.2020.]

Sažetak
The paper presents the results of the study of the production process of balls in a special closed die, which performs a full compression due to the alternate insertion of rams. The possibility of implementing the proposed method is proved experimentally, and the presence of high compressive stresses in the deformation center is shown using the method of sliding lines and mathematical computer modeling. Due to the alternate insertion of rams, the process of plastic deformation is intensified, which makes it possible to obtain high-quality balls. The maximum average stress in the deformation center obtained by the theoretical calculation method of sliding lines is – 436,94 MPa, and the values obtained by mathematical computer modeling is – 500 MPa. Metallographic analysis showed that the grain diameter of the obtained ball samples in the central part, compared to the initial samples, was crushed 3 times (up to 5 μm).

Ključne riječi
high strength ball; forging; severe plastic deformation; stress-strain state; closed die; modelling

Hrčak ID: 241218

URI
https://hrcak.srce.hr/241218

Posjeta: 68 *