hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20190522104029

Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN

Amanda Aljinović ; Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, Ruđera Boškovića 32, 21 000 Split, Croatia
Boženko Bilić ; Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, Ruđera Boškovića 32, 21 000 Split, Croatia
Nikola Gjeldum ; Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, Ruđera Boškovića 32, 21 000 Split, Croatia
Marko Mladineo ; Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, Ruđera Boškovića 32, 21 000 Split, Croatia

Puni tekst: engleski, pdf (2 MB) str. 456-464 preuzimanja: 32* citiraj
APA 6th Edition
Aljinović, A., Bilić, B., Gjeldum, N. i Mladineo, M. (2021). Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN. Tehnički vjesnik, 28 (2), 456-464. https://doi.org/10.17559/TV-20190522104029
MLA 8th Edition
Aljinović, Amanda, et al. "Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN." Tehnički vjesnik, vol. 28, br. 2, 2021, str. 456-464. https://doi.org/10.17559/TV-20190522104029. Citirano 16.05.2021.
Chicago 17th Edition
Aljinović, Amanda, Boženko Bilić, Nikola Gjeldum i Marko Mladineo. "Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN." Tehnički vjesnik 28, br. 2 (2021): 456-464. https://doi.org/10.17559/TV-20190522104029
Harvard
Aljinović, A., et al. (2021). 'Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN', Tehnički vjesnik, 28(2), str. 456-464. https://doi.org/10.17559/TV-20190522104029
Vancouver
Aljinović A, Bilić B, Gjeldum N, Mladineo M. Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN. Tehnički vjesnik [Internet]. 2021 [pristupljeno 16.05.2021.];28(2):456-464. https://doi.org/10.17559/TV-20190522104029
IEEE
A. Aljinović, B. Bilić, N. Gjeldum i M. Mladineo, "Prediction of Surface Roughness and Power in Turning Process Using Response Surface Method and ANN", Tehnički vjesnik, vol.28, br. 2, str. 456-464, 2021. [Online]. https://doi.org/10.17559/TV-20190522104029

Sažetak
This paper examines the influence of three cutting parameters (cutting speed, cutting depth and feed rate) on surface roughness and power in the longitudinal turning process of aluminium alloy. For the analysis of data gathered by experiments, two methods for prediction of responses were employed, namely Response Surface Methodology (RSM) and Artificial Neural Network (ANN). The research has shown that the ANN gives a better prediction of surface roughness than the RSM. In the modelling of the power, the average error value obtained by the ANN does not differ significantly from its value obtained by the RSM. This research is conducted to reveal the rigidity of the machine tool in order to select an appropriate spindle motor for retrofit purpose. The unexpected surface roughness and the error between the experimental and predicted values show that the obtained models are, in most cases, not adequate to predict surface roughness when the power is greater than a given limit. Therefore, the servo motor with smaller power than the original motor is selected which is cost-effective and it will not cause inappropriate strong vibrations that lead to the unexpected surface roughness and excessive noise inside the Learning Factory environment in which the machine tool is used.

Ključne riječi
artificial neural network (ANN); power; response surface method (RSM); surface roughness

Hrčak ID: 255812

URI
https://hrcak.srce.hr/255812

Posjeta: 66 *