hrcak mascot   Srce   HID

Izvorni znanstveni članak

Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium

G. Kugler
R. Turk
T. Večko-Pirtovšek
M. Terčelj

Puni tekst: engleski, pdf (1 MB) str. 21-29 preuzimanja: 2.524* citiraj
APA 6th Edition
Kugler, G., Turk, R., Večko-Pirtovšek, T. i Terčelj, M. (2006). Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium. Metalurgija, 45 (1), 21-29. Preuzeto s https://hrcak.srce.hr/6503
MLA 8th Edition
Kugler, G., et al. "Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium." Metalurgija, vol. 45, br. 1, 2006, str. 21-29. https://hrcak.srce.hr/6503. Citirano 22.02.2020.
Chicago 17th Edition
Kugler, G., R. Turk, T. Večko-Pirtovšek i M. Terčelj. "Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium." Metalurgija 45, br. 1 (2006): 21-29. https://hrcak.srce.hr/6503
Harvard
Kugler, G., et al. (2006). 'Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium', Metalurgija, 45(1), str. 21-29. Preuzeto s: https://hrcak.srce.hr/6503 (Datum pristupa: 22.02.2020.)
Vancouver
Kugler G, Turk R, Večko-Pirtovšek T, Terčelj M. Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium. Metalurgija [Internet]. 2006 [pristupljeno 22.02.2020.];45(1):21-29. Dostupno na: https://hrcak.srce.hr/6503
IEEE
G. Kugler, R. Turk, T. Večko-Pirtovšek i M. Terčelj, "Wear Beahaviour of Nitrided Microstructures of AlSl H13 Dies for Hot Extrusion of Aluminium", Metalurgija, vol.45, br. 1, str. 21-29, 2006. [Online]. Dostupno na: https://hrcak.srce.hr/6503. [Citirano: 22.02.2020.]

Sažetak
Nitriding of bearing surfaces on dies (tools, AISI H13) for hot extrusion of aluminium is technologically a very sensitive process with regard to achieving a constant quality of the nitrided layers. This study was based on the analysis of microstructure on dies with intentionally prepared deep and narrow gaps which were nitrided by various manufacturers of equipment for gas and ionic nitriding. The manufacturers chose their own nitriding parameters in order to achieve an optimal wear resistant microstructure. The microstructures obtained showed differences with regard to the presence or absence of a compound layer (white layer), its thickness and its e/g' phase ratio (XRD), nitriding depth and microhardness profile. The measured nitriding depths and the maximum microhardness values on nitrided surface layers were quite similar on dies of the same manufacturer, while for different manufacturers these values differed. Differences with regards to compound layer characteristics were also found on the same die. The die samples with these various nitrided microstructures were then laboratory tested for wear resistance using equipment that provides simulation of the tribological conditions during hot extrusion of aluminium. The wear testing results show differences in behaviour of the nitrided samples. The differences in the actual structures, microstructures, hardness, etc. explain the high level of scattering in die life in actual industrial applications.

Ključne riječi
Aluminium hot extrusion; H13 die steel; nitrided microstructures; compound layer; XRD; wear resistance

Hrčak ID: 6503

URI
https://hrcak.srce.hr/6503

Posjeta: 2.930 *