hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20181228185947

Experimental Investigation of Delamination Formed by Bone Drilling

Serdar Koluaçik   ORCID icon orcid.org/0000-0002-1450-4029 ; Department of Orthopedics and Traumatology, Malatya Training and Research Hospital, 44090 Malatya, Turkey
Murat Can ; Department of Orthopedics and Traumatology, Malatya Training and Research Hospital, 44090 Malatya, Turkey
Erkan Bahçe   ORCID icon orcid.org/0000-0001-5389-5571 ; Department of Mechanical Engineering, Inonu University, 44210 Malatya, Turkey

Puni tekst: engleski, pdf (3 MB) str. 711-717 preuzimanja: 117* citiraj
APA 6th Edition
Koluaçik, S., Can, M. i Bahçe, E. (2020). Experimental Investigation of Delamination Formed by Bone Drilling. Tehnički vjesnik, 27 (3), 711-717. https://doi.org/10.17559/TV-20181228185947
MLA 8th Edition
Koluaçik, Serdar, et al. "Experimental Investigation of Delamination Formed by Bone Drilling." Tehnički vjesnik, vol. 27, br. 3, 2020, str. 711-717. https://doi.org/10.17559/TV-20181228185947. Citirano 30.10.2020.
Chicago 17th Edition
Koluaçik, Serdar, Murat Can i Erkan Bahçe. "Experimental Investigation of Delamination Formed by Bone Drilling." Tehnički vjesnik 27, br. 3 (2020): 711-717. https://doi.org/10.17559/TV-20181228185947
Harvard
Koluaçik, S., Can, M., i Bahçe, E. (2020). 'Experimental Investigation of Delamination Formed by Bone Drilling', Tehnički vjesnik, 27(3), str. 711-717. https://doi.org/10.17559/TV-20181228185947
Vancouver
Koluaçik S, Can M, Bahçe E. Experimental Investigation of Delamination Formed by Bone Drilling. Tehnički vjesnik [Internet]. 2020 [pristupljeno 30.10.2020.];27(3):711-717. https://doi.org/10.17559/TV-20181228185947
IEEE
S. Koluaçik, M. Can i E. Bahçe, "Experimental Investigation of Delamination Formed by Bone Drilling", Tehnički vjesnik, vol.27, br. 3, str. 711-717, 2020. [Online]. https://doi.org/10.17559/TV-20181228185947

Sažetak
Bone drilling is a common method for fixing implants used in bone fractures. Because of the fibre-reinforced composite structure of bone, parameters such as
feed rate, spindle speed and drill type affect the hole surface quality. After drilling, the quality of the bore surface, burr formation and delamination at the hole entrance and
exit affect the ability of the screw to cause implant failure and fusion problems of the fracture. For this reason, it is very important to conduct drilling with optimum speed and
feedrate values. In this study, the effects of processing parameters on hole surface quality and delamination were studied experimentally. In the experiment, bovine bone,
which has similar structural properties to human bone, was used. The hole surface quality and delamination formed at the exit of the hole were examined for three different
feed rates and spindle speeds. As a result of the experiments, it was seen that the feed rate had more effect on both delamination and hole surface quality than the spindle
speed. It was also determined that the cortical part of the bone and the cancellous part of the bone affected the production of heat and drill wear differently.

Ključne riječi
bone drilling; delamination; surface quality

Hrčak ID: 239077

URI
https://hrcak.srce.hr/239077

Posjeta: 206 *