hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20200414111241

Research on the End Surface Dent of the Main Shaft Forging

Liyong Ni ; University of Electronic Science and Technology of China, Zhongshan Institute, Zhongshan, 528402, China
Longjiang Niu* ; School of Mechanical Engineering, Shanghai Dianji University, Shanghai, 201306 China
Daoxiang Qian ; V-Strong Electronics CO., LTD, Guangdong Shenzhen 518048, China
Suoqing Yu ; Xingtai Polytechnic College, Xingtai, 054035, China
Chenyu Ye ; University of Electronic Science and Technology of China, Zhongshan Institute, Zhongshan, 528402, China
Yibin Cai ; Liaoning Zhongwang Group CO., LTD, Shenzhen 518110, China

Puni tekst: engleski, pdf (1 MB) str. 433-438 preuzimanja: 18* citiraj
APA 6th Edition
Ni, L., Niu*, L., Qian, D., Yu, S., Ye, C. i Cai, Y. (2021). Research on the End Surface Dent of the Main Shaft Forging. Tehnički vjesnik, 28 (2), 433-438. https://doi.org/10.17559/TV-20200414111241
MLA 8th Edition
Ni, Liyong, et al. "Research on the End Surface Dent of the Main Shaft Forging." Tehnički vjesnik, vol. 28, br. 2, 2021, str. 433-438. https://doi.org/10.17559/TV-20200414111241. Citirano 16.05.2021.
Chicago 17th Edition
Ni, Liyong, Longjiang Niu*, Daoxiang Qian, Suoqing Yu, Chenyu Ye i Yibin Cai. "Research on the End Surface Dent of the Main Shaft Forging." Tehnički vjesnik 28, br. 2 (2021): 433-438. https://doi.org/10.17559/TV-20200414111241
Harvard
Ni, L., et al. (2021). 'Research on the End Surface Dent of the Main Shaft Forging', Tehnički vjesnik, 28(2), str. 433-438. https://doi.org/10.17559/TV-20200414111241
Vancouver
Ni L, Niu* L, Qian D, Yu S, Ye C, Cai Y. Research on the End Surface Dent of the Main Shaft Forging. Tehnički vjesnik [Internet]. 2021 [pristupljeno 16.05.2021.];28(2):433-438. https://doi.org/10.17559/TV-20200414111241
IEEE
L. Ni, L. Niu*, D. Qian, S. Yu, C. Ye i Y. Cai, "Research on the End Surface Dent of the Main Shaft Forging", Tehnički vjesnik, vol.28, br. 2, str. 433-438, 2021. [Online]. https://doi.org/10.17559/TV-20200414111241

Sažetak
In the process of the stretching of the shaft forgings, if the process parameters are not properly selected, the end-face dent will take place. The end-face dent affects the performance of large forgings and leads to much material wasting. Finite element method was employed to perform numerical simulation of the stretching of a main shaft with an upper flat anvil and a lower V-shaped anvil. The orthogonal test table was designed by selecting the anvil width, the Reduction ratio and the feed as influencing factors. Accordingly, simulations were carried out to solve the end-face dent values under different parameter combinations. The analysis showed that the optimal parameter combination gave an anvil width ratio of 0.75, a Reduction ratio of 0.2, and an initial feed of 300 mm. Through extremum difference analysis, it was found that among the three factors are the feed, the reduction ratio, and the anvil width ratio in the decreasing order of the influence on the end- face dent. Comprehensive analysis showed that when the anvil is relatively narrow, increasing the relative feed can reduce the end-surface dent remarkably. It is advisable that during the stretching of shaft forgings with a flat upper anvil and a V-shaped lower anvil, the combination of the anvil width ratio of 0.75, the reduction ratio of 0.2, and increasing the feed can reduce the end-face dent, thereby reducing the end cutting and saving material costs.

Ključne riječi
dent; finite element method; heavy forgings; stretching

Hrčak ID: 255809

URI
https://hrcak.srce.hr/255809

Posjeta: 47 *