hrcak mascot   Srce   HID

Izvorni znanstveni članak
https://doi.org/10.17559/TV-20180706121545

Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles

Goran Heffer ; Faculty of Agrobiotechnical Sciences Osijek, Josip Juraj Strossmayer University of Osijek, Vladimira Preloga 1, 31 000 Osijek, Croatia
Ivan Samardžić ; Mechanical Engineering Faculty in Slavonski Brod, Josip Juraj Strossmayer University of Osijek, Trg Ivane Brlić-Mažuranić 2, 35 000 Slavonski Brod, Croatia
Zdravko Schauperl ; University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture, Ivana Lučića 5, 10 000 Zagreb, Croatia
Ivan Vidaković ; Faculty of Agrobiotechnical Sciences Osijek, Josip Juraj Strossmayer University of Osijek, Vladimira Preloga 1, 31 000 Osijek, Croatia

Puni tekst: engleski, pdf (2 MB) str. 1776-1782 preuzimanja: 98* citiraj
APA 6th Edition
Heffer, G., Samardžić, I., Schauperl, Z. i Vidaković, I. (2018). Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles. Tehnički vjesnik, 25 (6), 1776-1782. https://doi.org/10.17559/TV-20180706121545
MLA 8th Edition
Heffer, Goran, et al. "Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles." Tehnički vjesnik, vol. 25, br. 6, 2018, str. 1776-1782. https://doi.org/10.17559/TV-20180706121545. Citirano 16.06.2019.
Chicago 17th Edition
Heffer, Goran, Ivan Samardžić, Zdravko Schauperl i Ivan Vidaković. "Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles." Tehnički vjesnik 25, br. 6 (2018): 1776-1782. https://doi.org/10.17559/TV-20180706121545
Harvard
Heffer, G., et al. (2018). 'Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles', Tehnički vjesnik, 25(6), str. 1776-1782. doi: https://doi.org/10.17559/TV-20180706121545
Vancouver
Heffer G, Samardžić I, Schauperl Z, Vidaković I. Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles. Tehnički vjesnik [Internet]. 2018 [pristupljeno 16.06.2019.];25(6):1776-1782. doi: https://doi.org/10.17559/TV-20180706121545
IEEE
G. Heffer, I. Samardžić, Z. Schauperl i I. Vidaković, "Wear of Induction Cladded Coating in the Abrasive Mass at Various Speeds and Impact Angles", Tehnički vjesnik, vol.25, br. 6, str. 1776-1782, 2018. [Online]. doi: https://doi.org/10.17559/TV-20180706121545

Sažetak
The wear of induction cladded coating during motion was investigated through the abrasive mass at a speed of 1.0 to 3.0 m/s and the impact angle of abrasive particles with a worn surface of 0° to 90°. Cladding was performed by using Ni-Cr-Si-B-Fe flame spraying powder. Experimental research was carried out by using the Response Surface Method (RSM) and Central Composite Design (CCD). Analysis of variance proved that both motion speed and impact angle had significant impact on the wear of coating, both individually and interactively. Motion speed had the greatest influence, and the interaction of speed and angle had the least influence. The wear rate increased along with the motion speed increase, and the influence of the impact angle depends on the wear speed. At a speed of 1 m/s, the wear increases along with the increase of angle from 0° to 45° and then continues to decrease up to the angle of 90°. At a speed of 2 m/s, the wear increases along with the angle increase from 0° to 30° and then continues to decrease up to the angle of 90°. At a speed of 3 m/s, the wear increases along with the angle increase from 0° to 20° and then decreases as the angle increases up to 90°. Based on the statistical data processing, this research developed the mathematical model of wear in the form of quadratic polynomial that describes the influences of input variables in individual and interactive form.

Ključne riječi
abrasive mass; flame spraying powder; impact angle; induction cladded coating; motion speed; wear rate

Hrčak ID: 212834

URI
https://hrcak.srce.hr/212834

Posjeta: 176 *