hrcak mascot   Srce   HID

Metalurgija, Vol. 53 No. 4, 2014.


Metalurgija,Vol. 53 No. 4
Datum izdavanja: listopada 2014.

Objavljen na Hrčku: 1. 6. 2014.
Sadržaj Puni tekst
30 years as Editor-in-chief of Metalurgija -Acad. Ilija Mamuzić, D. Sc. D.h.c. Prof. h.c. engleskipdf 637 KB
30 godina kao Glavni i odgovorni urednik - Acad. Ilija Mamuzić, D. Sc. D.h.c. Prof. h.c. (str.437-438)  
Ostalo  
Effect of the structural parameters changes in the multi-strand tundish on the non-metallic inclusions distribution and separation (str.439-442) engleskipdf 966 KB
M. Warzecha, T. Merder, P. Warzecha
Izvorni znanstveni članak
 
Influence of design parameters of tundish and technological parameters of steel continuous casting on the hydrodynamics of the liquid steel flow (str.443-446) engleskipdf 859 KB
T. Merder
Izvorni znanstveni članak
 
An experimental study on the air delivery and gas removal method in a model of furnace for ferroalloy production (str.447-450) engleskipdf 1 MB
S. Gil, J. Góral, J. Ochman, M. Saternus, W. Bialik
Izvorni znanstveni članak
 
Emission of polycyclic aromatic hydrocarbons (PAHs) and benzene, toluene, ethylbenzene and xylene (BTEX) from the furan moulding sands with addition of the reclaim (str.451-454) engleskipdf 888 KB
M. Holtzer, A. Bobrowski, R. Dańko, A. Kmita, S. Żymankowska-Kumon, M. Kubecki, M. Górny
Izvorni znanstveni članak
 
Improve the humidity resistance of sodium silicate sands by ester-microwave composite hardening (str.455-458) engleskipdf 843 KB
W. Huafang, G. Wenbang, L. Jijun
Izvorni znanstveni članak
 
Cohesion and adhesion properties of modified water glass with colloidal solutions of ZnO (str.459-462) engleskipdf 1 MB
K. Smyksy, A. Kmita, B. Hutera, D. Drożyński, B. Stypuła, M. Hajos, M. Starowicz
Izvorni znanstveni članak
 
Synthesis and character of cerium oxide (CeO2) nanoparticles by the precipitation method (str.463-465) engleskipdf 859 KB
Y. H. Liu, J. C. Zuo, X. F. Ren, L. Yong
Izvorni znanstveni članak
 
Identification of low cycle fatigue parameters of high strength low-alloy (HSLA) steel at room temperature (str.466-468) engleskipdf 1 MB
S. Bulatović, Lj. Milović, A. Sedmak, I. Samardžić
Izvorni znanstveni članak
 
Microstructure of NiTi orthodontic wires observations using transmission electron microscopy (str.469-472) engleskipdf 869 KB
J. Ferčec, D. Jenko, B. Buchmeister, F. Rojko, B. Budič, B. Kosec, R. Rudolf
Izvorni znanstveni članak
 
Change of ears creation of AHSS steels after heat treatment of zinc coating (str.473-476) engleskipdf 902 KB
E. Spišák, J. Majerníková, J. Slota
Izvorni znanstveni članak
 
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue (str.477-480) engleskipdf 1 MB
S. Bulatović, Z. Burzić, V. Aleksić, A. Sedmak, Lj. Milović
Izvorni znanstveni članak
 
Fatigue crack growth and fracture mechanics analysis of a working roll surface layer material (str.481-484) engleskipdf 1 MB
M. Drobne, T. Vuherer, I. Samardžić, S. Glodež
Izvorni znanstveni članak
 
Numerical analysis of AZ61 magnesium alloy extrusion process by modified equal channel angular extrusion (ECAE) method (str.485-488) engleskipdf 944 KB
T. Bajor, M. Krakowiak, P. Szota
Izvorni znanstveni članak
 
Physical modelling of plastic deformation conditions for the rolling proces of AZ31 bars in a three high skew rolling mill (str.489-492) engleskipdf 1 MB
A. Gryc, T. Bajor, H. Dyja, S. Sawicki, K. Laber
Izvorni znanstveni članak
 
The influence of the hardening coolant agent on the properties of hot rolled bars of the steel 42CrMo4 (str.493-496) engleskipdf 1 MB
M. Stańczyk, T. Figlus
Izvorni znanstveni članak
 
Numerical investigation of producing a Ti6Al4V alloy jaw coupling sleeve-disk by orbital forging (str.497-500) engleskipdf 1 MB
G. Samołyk
Izvorni znanstveni članak
 
The influence of the shape of grooves on the behavior of internal material discontinuities in continuous S355J2G3 steel strands during rolling (str.501-504) engleskipdf 948 KB
H. Dyja, K. Sobczak, A. Kawałek
Izvorni znanstveni članak
 
Forming a lever preform made of aluminium alloy 2014 (str.505-508) engleskipdf 963 KB
T. Bulzak, J. Tomczak, Z. Pater
Izvorni znanstveni članak
 
Micro friction stir welding of copper electrical contacts (str.509-512) engleskipdf 942 KB
D. Klobčar, J. Tušek, M. Bizjak, V. Lešer
Izvorni znanstveni članak
 
Structural, chemical and deformation changes in friction welded joint of dissimilar steels (str.513-516) engleskipdf 862 KB
N. Ratković, R. Nikolić, I. Samardžić
Izvorni znanstveni članak
 
Problems in laser repair welding of polished surfaces (str.517-520) engleskipdf 916 KB
A. Skumavc, J. Tušek, M. Mulc, D. Klobčar
Izvorni znanstveni članak
 
Investigation of sequential cryogenic hard turning and ball burnishing processes (str.521-525) engleskipdf 1 MB
K. Żak, W. Grzesik, M. Prażmowski
Izvorni znanstveni članak
 
Analysis of residual stresses on the transverse beam of a casting stand by means of drilling method (str.526-528) engleskipdf 1 MB
P. Frankovský, F. Šimčák
Izvorni znanstveni članak
 
Microhardness changes gradient of the duplex stainless steel (DSS) surface layer after dry turning (str.529-532) engleskipdf 904 KB
G. Krolczyk, P. Nieslony, S. Legutko, A. Stoic
Izvorni znanstveni članak
 
Monitoring of focusing tube wear during abrasive waterjet (AWJ) cutting of AISI 309 (str.533-536) engleskipdf 957 KB
P. Hreha, A. Radvanská, J. Cárach, D. Lehocká, K. Monková, G. Krolczyk, A. Ruggiero, I. Samardzić, D. Kozak, S. Hloch
Izvorni znanstveni članak
 
Abrasive waterjet (AWJ) titanium tangential turning evaluation (str.537-540) engleskipdf 1 MB
S. Hloch, J. Hlaváček, K. Vasilko, J. Cárach, I. Samardžić, D. Kozak, I. Hlavatý, J. J. Ščučka, J. Klich, D. Klichová
Izvorni znanstveni članak
 
Application of photostress method in stress analysis of a rotating disc (str.541-544) engleskipdf 1 MB
P. Frankovský, F. Trebuňa
Izvorni znanstveni članak
 
Risk based on quality, environmental and occupational safety in heat treatment processes (str.545-548) engleskipdf 864 KB
T. Karkoszka, M. Soković
Izvorni znanstveni članak
 
Alkaline carbonates in blast furnace process (str.549-552) engleskipdf 702 KB
P. Besta, A. Samolejová, R. Lenort, K. Janovská, J. Kutáč, A. Sikorová
Prethodno priopćenje
 
Management of the pig iron Si and slag CaO/SiO2 technological indicators in order to produce pig iron with a titanium content below 0,02 %Ti (str.553-555) engleskipdf 720 KB
C. Kolmasiak, I. Nowodzińska-Budzik, R. Budzik
Prethodno priopćenje
 
Studying and improving blast furnace cast iron quality (str.556-558) engleskipdf 882 KB
T. K. Balgabekov, D. K. Issin, B. M. Kimanov, A. Z. Issagulov, Zh. D. Zholdubayeva, A. Z. Akashev, B. D. Issin
Prethodno priopćenje
 
Harmful admixtures assessment in sinter mixtures used in iron ore sinter plants in Poland (str.559-562) engleskipdf 911 KB
J. Korol, D. Burchart-Korol, A. Smoliński
Prethodno priopćenje
 
Silicon production using long flaming coal and improvement of its quality indicators (str.563-566) engleskipdf 724 KB
A. D. Mekhtiev, M. J. Tolymbekov, A. V. Kim, Zh. D. Zholdubaeva, D. K. Issin, A. Z. Issagulov, B. D. Issin
Prethodno priopćenje
 
The model for the calculation of the dispersed iron ore resource purchase cost in the world class manufacturing (WCM) logistics pillar context (str.567-570) engleskipdf 806 KB
M. Dudek
Prethodno priopćenje
 
Calculation of the boundary conditions in the continuous casting of steel process (str.571-573) engleskipdf 865 KB
K. Miłkowska-Piszczek, J. Falkus
Prethodno priopćenje
 
Effects of a bath composition on aluminium loss during Ti-Al alloy smelting in a vacuum induction furnace (str.574-576) engleskipdf 1018 KB
L. Blacha, K. Michalek, A. Smalcerz, M. Warzecha
Prethodno priopćenje
 
Pyrometallurgical slags as a potential source of selected metals recovery (str.577-580) engleskipdf 860 KB
K. Nowińska, Z. Adamczyk, E. Melaniuk-Wolny
Prethodno priopćenje
 
Studying properties of carbonaceous reducers and process of forming primary titanium slags (str.581-584) engleskipdf 867 KB
T. K. Balgabekov, S. O. Baissanov, D. K. Issin, Zh. D. Zholdubayeva, A. Z. Akashev, A. S. Baissanov, B. D. Issin
Prethodno priopćenje
 
Reduction of copper slag with the use of carbon granulates (str.585-587) engleskipdf 902 KB
G. Siwiec, B. Oleksiak, T. Matuła, L. Socha, W. Stanek
Prethodno priopćenje
 
Melting and casting of ingots made of an Mg - Li type alloys (str.588-590) engleskipdf 898 KB
T. Mikuszewski
Prethodno priopćenje
 
Compressive stresses of mould mixture (str.591-593) engleskipdf 976 KB
G. Solenicki, I. Budic, I. Kladaric, D. Novoselovic
Prethodno priopćenje
 
Influence of process parameters on castability at full mold casting (str.594-596) engleskipdf 1 MB
I. Budic, D. Novoselovic, I. Samardzic
Prethodno priopćenje
 
Long - range foundry Al composite alloys (str.597-600) engleskipdf 924 KB
A. D. Mekhtiev, A. G. Kosnikov, D. K. Issin, Zh. D. Zholdubaeva, B. D. Issin
Prethodno priopćenje
 
Developing technological process of obtaining giality casts (str.601-604) engleskipdf 900 KB
A. Issagulov, V. Kulikov, D. Issagulova, E. Shcherbakova, A. Kuszhanova
Prethodno priopćenje
 
The obtained of concentrates containing precious metals for pyrometallurgical processing (str.605-608) engleskipdf 899 KB
B. Oleksiak, G. Siwiec, A. Blacha-Grzechnik, J. Wieczorek
Prethodno priopćenje
 
Possibilities of platinum recovery from metal supported spent auto catalysts (str.609-612) engleskipdf 845 KB
A. Fornalczyk, J. Cebulski, M. Saternus, J. Willner
Prethodno priopćenje
 
Characteristics of low nickel ferritic-austenitic corrosion resistant cast steel (str.613-616) engleskipdf 1 MB
B. Kalandyk, R. Zapała, S. Sobula, M. Górny, L. Boroń
Prethodno priopćenje
 
Analysis of material reliability of AlSi17Cu5 alloy using statistical weibull distribution (str.617-620) engleskipdf 950 KB
J. Piątkowski, M. Jabłońska
Prethodno priopćenje
 
Cr - Ni system alloys composition impact on durability value (str.621-623) engleskipdf 761 KB
A. Z. Issagulov, S. S. Kvon, V. Yu. Kulikov, A. A. Sakbossynova
Prethodno priopćenje
 
Cold weld cracking susceptibility of high strength low alloyed (HSLA) steel NIONIKRAL 70 (str.624-626) engleskipdf 1 MB
A. S. Tawengi, A. Sedmak, V. Grabulov
Prethodno priopćenje
 
Weldability prediction of high strength steel S960QL after weld thermal cycle simulation (str.627-630) engleskipdf 1 MB
M. Dunđer, T. Vuherer, I. Samardžić
Prethodno priopćenje
 
Refurbishment of damaged tools using the combination of GTAW and laser beam welding (str.631-633) engleskipdf 796 KB
J. Tušek, A. Skumavc, K. Pompe, D. Klobčar
Prethodno priopćenje
 
The stress–strain state of the cracked welded joint between the header and the shell of PGV-1000M steam generator (str.634-636) engleskipdf 898 KB
S. M. Ban’ko, S. V. Kobel’skii, I. Samardžić
Prethodno priopćenje
 
Impact energy analysis of quenched and tempered fine grain structural steel specimens after weld thermal cycle simulation (str.637-640) engleskipdf 1 MB
M. Dunđer, T. Vuherer, I. Samardžić
Prethodno priopćenje
 
FEM analysis of hollow hub forming in rolling extrusion process (str.641-644) engleskipdf 971 KB
J. Bartnicki
Prethodno priopćenje
 
Theoretical and experimental research of hammer forging process of RIM from AZ31 magnesium alloy (str.645-648) engleskipdf 995 KB
A. Gontarz
Prethodno priopćenje
 
Rotary compression process for producing toothed hollow shafts (str.649-652) engleskipdf 1 MB
J. Tomczak
Prethodno priopćenje
 
Analysis of the helical-wedge rolling process for producing a workholding bolt (str.653-656) engleskipdf 943 KB
Z. Pater
Prethodno priopćenje
 
Research on deformations which appear in within the metal structures of mining equipment (str.657-660) engleskipdf 831 KB
G. Paraschiv, D. Dobrotă
Prethodno priopćenje
 
Assessment of properties thermal sprayed coatings realised using cermet blend powder (str.661-664) engleskipdf 908 KB
J. Brezinová, A. Guzanová, E. Spišák
Prethodno priopćenje
 
A model for the pavement temperature prediction at specified depth using neural networks (str.665-667) engleskipdf 912 KB
B. Matić, D. Matić, S. Sremac, N. Radović, P. Viđikant
Prethodno priopćenje
 
Reflection of the economic rate of return in the efficiency use of the fixed and current assets with study case in mettalurgy (str.668-672) engleskipdf 799 KB
C. Căruntu, L. M. Lăpăduşi
Prethodno priopćenje
 
Diagnosis of the wear of gears in the gearbox using the wavelet packet transform (str.673-676) engleskipdf 909 KB
T. Figlus, M. Stańczyk
Prethodno priopćenje
 
Reducing harmful effects of metals in water (str.677-680) engleskipdf 797 KB
I. Tepić, G. Tepić, P. Viđikant, T. Pejakov, R. Kulundžić
Prethodno priopćenje
 
Material flow enhancement in production assembly lines under application of zoned order picking systems (str.681-684) engleskipdf 750 KB
D. Živanić, G. Vujić, B. Kosec, A. Stoić
Prethodno priopćenje
 
Production of technical silicon and silicon carbide from rice-husk (str.685-688) engleskipdf 699 KB
A. Z. Issagulov, V. A. Kim, S. S. Kvon, V. Yu. Kulikov, A. U. Tussupova
Prethodno priopćenje
 
Transformers as a potential for soil contamination (str.689-692) engleskipdf 782 KB
N. Stojić, M. Pucarević, D. Mrkajić, I. Kecojević
Prethodno priopćenje
 
Development of polymer packaging for power cable (str.693-696) engleskipdf 787 KB
S. Sremac, P. Gladović, M. Đelošević, B. Matić, A. Matić
Prethodno priopćenje
 
The state of art and foresight of world’s casting production (str.697-700) engleskipdf 830 KB
M. Holtzer, R. Dańko, S. Żymankowska-Kumon
Pregledni rad
 
Ergonomic and work safety evaluation criteria of process excellence in the foundry industry (str.701-704) engleskipdf 730 KB
M. Butlewski, A. Misztal, M. Jasiulewicz-Kaczmarek, S. Janik
Pregledni rad
 
Some viewpoints of materials forming technology (str.705-708) engleskipdf 882 KB
J. Kliber
Pregledni rad
 
The use of value stream mapping to introduction of organizational innovation in industry (str.709-712) engleskipdf 726 KB
R. Wolniak, B. Skotnicka-Zasadzien
Pregledni rad
 
Export, import, production and use of wire in the Czech Republic (str.713-716) engleskipdf 834 KB
P. Plunder, I. Vozňáková, A. Samolejová, K. Janovská
Pregledni rad
 
Guidelines for the rail grade selection (str.717-720) engleskipdf 854 KB
M. Tomičić-Torlaković
Pregledni rad
 
Managing rail service life (str.721-724) engleskipdf 1018 KB
Z. Popović, L. Lazarević, Lj. Brajović, P. Gladović
Pregledni rad
 
Formation and planning of virtual production networks (VPN) in metallurgical clusters (str.725-727) engleskipdf 715 KB
S. Saniuk, A. Saniuk, R. Lenort, A. Samolejova
Pregledni rad
 
The application of winning key metrics in a metallurgical firm (str.728-730) engleskipdf 829 KB
M. Mikušová, P. Horváthová, K. Janovská, A. Samolejová
Pregledni rad
 
Investment gold: exemption from tax (VAT) in the Romanian fiscal system (str.731-733) engleskipdf 1 MB
I. Bostan
Pregledni rad
 
Posjeta: 79.651 *