hrcak mascot   Srce   HID

Metallurgy, Vol. 55 No. 4, 2016


Metallurgy,Vol. 55 No. 4
Publication date: October 2016

Published on HRČAK: 08 May 2016
Table of contents Full text
Optimization utilization of vanadium - titanium iron ore in sintering based on orthogonal method (str.581-584) englishpdf 223 KB
M. Zhou, T. Jiang, S. T. Yang, K. Ma, X. X. Xue, W. J. Zhang
Original scientific paper
 
Effect of CaO/SiO2 ratio on melting property and strength of sinter with vanadium-titanium iron ore addition (str.585-588) englishpdf 213 KB
S. T. Yang, M. Zhou, T. Jiang, X. X. Xue, P. N. Duan, W. J. Zhang
Original scientific paper
 
Ecological water-based protective coatings for moulds and cores of iron castings (str.589-592) englishpdf 360 KB
A. Kmita, J. Zych, M. Holtzer, J. Mocek, S. Piasny
Original scientific paper
 
Magnetic field distribution in the electromagnetic feeding riser of rectangle steel ingot (str.593-596) englishpdf 210 KB
C. J. Xu, Y. X. Zeng, Z. L. Wang, J. Li, S. L. Li, X. J. Zhang
Original scientific paper
 
Study on unidirectional solidification ingot with hollow lateral wall insulation (str.597-600) englishpdf 228 KB
G. W. Ao, M. G. Shen, Z. S. Zang, B. L. Li
Original scientific paper
 
Study on stirring behavior of liquid steel in bottom-blowing ladle with immersed cylinder (str.601-604) englishpdf 151 KB
M. G. Shen, H. D. Zhang, C. Wu, Q. Xu, Q. H. Qi
Original scientific paper
 
Study on the influence of groove mold on the character of casting (str.605-608) englishpdf 231 KB
M. G. Shen, R. T. Zhang
Original scientific paper
 
The influence of the ionic reactions on the refining secondary raw materials (str.609-612) englishpdf 280 KB
P. Schlafka, A. W. Bydałek, M. Holtzer, W. Wołczyński
Original scientific paper
 
Properties and structure of the weld joints of quench and tempered 4330V steel (str.613-616) englishpdf 375 KB
M. Zuk, J. Gorka, A. Czuprynski, M. Adamiak
Original scientific paper
 
Active flux tungsten inert gas welding of austenitic stainless steel AISI 304 (str.617-620) englishpdf 358 KB
D. Klobčar, Tušek, M. Bizjak, S. Simončič, V. Lešer
Original scientific paper
 
Influence of heat treatment on the structural and magnetic characteristics of (NdxPr1-x)2Fe14B-based magnetic material for low-temperature application (str.621-624) englishpdf 187 KB
K. Skotnicová, G. S. Burkhanov, Y. S. Koshkid’ko, D. Růžička, T. Čegan, J. Cwik, N. B. Kolchugina, A. A. Lukin, O. Životský, K. Hrabovská
Original scientific paper
 
The analysis of the plastic deformation of two-layered magnesium – aluminium alloys (AZ31 – Al) (str.625-627) englishpdf 180 KB
R. Mola, S. Mróz, P. Szota, S. Sawicki
Original scientific paper
 
The theoretical and experimental analysis of the possibility of employing the groove rolling process for the manufacture of Mg/Al bimetallic bars (str.628-630) englishpdf 166 KB
S. Mróz, P. Szota, A. Stefanik
Original scientific paper
 
Determining the amount of Lüders band in niobium microalloyed steel (str.631-634) englishpdf 235 KB
I. Jandrlić, S. Rešković, F. Vodopivec
Original scientific paper
 
Determination of characteristics of plasticity of selected medium and high carbon steel grades in hot torsion test (str.635-638) englishpdf 275 KB
K. Laber, H. Dyja, A. Kawałek, S. Sawicki
Original scientific paper
 
The effect of relative deformation on the energy-force parameters in the asymmetrical plate rolling process (str.639-642) englishpdf 165 KB
A. Kawałek
Original scientific paper
 
High-temperature characteristics of 20MnB4 and 30MnB4 micro-addition cold upsetting steels and C45 and C70 high-carbon-steels (str.643-646) englishpdf 278 KB
S. Sawicki, H. Dyja, A. Kawałek, M. Knapiński, M. Kwapisz, K. Laber
Original scientific paper
 
The impact of the heat treatment parameters on patenting line on mechanical-technological properties of steel cord wires (str.647-650) englishpdf 174 KB
R. Kruzel, M. Suliga
Original scientific paper
 
The influence of lubricant carrier and lubrication conditions on mechanical-technological properties of high carbon steel wires (str.651-654) englishpdf 123 KB
M. Suliga, R. Kruzel
Original scientific paper
 
Phase transformation and cooling curves of the mild steel influenced by previous hot rolling (str.655-658) englishpdf 251 KB
S. Rusz, I. Schindler, P. Kawulok, R. Kawulok, P. Opěla, J. Kliber, Z. Solowski
Original scientific paper
 
Determination of technological parameters of saturated composites based on SiC by means of a model liquid (str.659-662) englishpdf 332 KB
K. Gawdzińska, L. Chybowski, J. A. Bejger, S. Krile
Original scientific paper
 
Sintering the beaks of the elevator manufactured by direct metal laser sintering (DMLS) process from Co - Cr alloy (str.663-666) englishpdf 212 KB
D. I. Băilă, C. V. Doicin, C. M. Cotruț, M. E. Ulmeanu, I. G. Ghionea, C. I. Tarbă
Original scientific paper
 
Comparison of deformation behavior of 316L stainless steel and Ti6Al4V alloy applied in traumatology (str.667-670) englishpdf 365 KB
M. Losertová, M. Štamborská, J. Lapin, V. Mareš
Original scientific paper
 
Research into boride layers growth kinetics on C45 carbon steel (str.671-674) englishpdf 203 KB
A. Milinović, V. Marušić, I. Samardžić
Original scientific paper
 
Corrosion properties of chromia based eco - friendly coatings on mild steel (str.675-678) englishpdf 233 KB
V. Brozek, P. Pokorny, P. Bouska, J. Stoulil, L. Mastny
Original scientific paper
 
Corrosion, friction and wear performance of diamond – like carbon (DLC) coatings (str.679-682) englishpdf 222 KB
M. Madej, D. Ozimina, R. Gałuszka, G. Gałuszka
Original scientific paper
 
Research on vibration damping on computer power supply box made of castermid material (str.683-686) englishpdf 213 KB
L. Dahil
Original scientific paper
 
Cyclic voltammetry study of Ce(IV)/Ce(III) redox couple and Ce(IV)-F complex in sulfuric acid medium (str.687-690) englishpdf 281 KB
J. G. He, Y. Li, X. X. Xue, H. Q. Ru, X. W. Huang, H. Yang
Original scientific paper
 
Crack growth through low-cycle fatigue loading of material ARMOX 500T (str.691-693) englishpdf 182 KB
V. Pepel, A. Žerovnik, R. Kunc, I. Prebil
Original scientific paper
 
Binder fraction reduction in non-ferrous metals concentrates briquetting process (str.694-696) englishpdf 188 KB
M. Jodkowski, J. Łabaj, J. Brzóska, D. Jama
Preliminary communication
 
Comprehensive study of rheological and surface properties of the selected slag system in the context of its internal structure (str.697-700) englishpdf 133 KB
L. Řeháčková, R. Dudek, S. Rosypalová, D. Matýsek, J. Dobrovská
Preliminary communication
 
Effect of cast steel production metallurgy on the emergence of casting defects (str.701-704) englishpdf 254 KB
L. Čamek, P. Lichý, I. Kroupová, J. Duda, J. Beňo, M. Korbáš, F. Radkovský, S. Bliznyukov
Preliminary communication
 
Measurement of casting parameters in ZnAlCu3 molds created by additive technology (str.705-708) englishpdf 277 KB
S. Medić, J. Groš, A. Horvatić, Ž. Kondić, L. Maglić
Preliminary communication
 
Studying possibility of smelting refined ferromanganese grades using silicon aluminum reducer (str.709-711) englishpdf 143 KB
A. Issagulov, N. Ospanov, A. Bayssanov, Ye. Makhambetov, D. Issagulova
Preliminary communication
 
Modelling of copper and zinc adsorption onto zeolite (str.712-714) englishpdf 151 KB
H. Pavolová, S. Khouri, M. Cehlár, L. Domaracká, M. Puzder
Preliminary communication
 
Improving production technology of tube steel grades in converter process (str.715-718) englishpdf 137 KB
P. V. Kovalev, S. V. Ryaboshuk, A. Z. Issagulov, V. Yu. Kulikov, Sv. S. Kvon, Y. P. Chsherbakova, G. I. Sultamurat, M. V. Jironkin
Preliminary communication
 
Optimizing the model of heating the material in the reheating furnace in metallurgy (str.719-722) englishpdf 186 KB
I. Špička, M. Heger, O. Zimný, Z. Jančíková, T. Tykva
Preliminary communication
 
Analysis of fuel savings in metallurgical furnaces with protective atmosphere (str.723-726) englishpdf 263 KB
S. Gil, W. Bialik, J. Ochman
Preliminary communication
 
Studying microstructure and phase composition of a new complex calcium containing alloy (str.727-729) englishpdf 260 KB
I. Bartenev, A. Issagulov, A. Baysanov, V. Roshchin, E. Makhambetov, G. Sirgetayeva, D. Issagulovа
Preliminary communication
 
Influence of induction hardening parameters on the GS30Mn5 weld properties (str.730-732) englishpdf 224 KB
V. Marušić, I. Samardžić, I. Opačak, L. Marušić
Preliminary communication
 
Experimental modeling of weld thermal cycle of the heat affected zone (HAZ) (str.733-736) englishpdf 287 KB
J. Kulhánek, P. Tomčík, R. Trojan, M. Juránek, P. Klaus
Preliminary communication
 
Tungsten inert gas (TIG) welding of aluminum alloy EN AW-AlZn5.5MgCu (str.737-740) englishpdf 293 KB
J. Tušek, D. Klobčar
Preliminary communication
 
Numerical simulation of the heat treatment of the weld for steam generator (str.741-744) englishpdf 226 KB
A. Macháčková, P. Kuchta, Z. Klečková, R. Kocich, J. Szwed
Preliminary communication
 
Impact strength of GX8CrNi12, GX5CrNi18-9 and GX5CrNiMo19-11-2 cast steel at - 30 °C (str.745-748) englishpdf 330 KB
B. Kalandyk, R. Zapała, J. Kasińska, B. Radoń
Preliminary communication
 
Modification influence of mischmetal on fractography fracture of G17CrMo5-5 cast steel samples after the three-point bending test (str.749-752) englishpdf 590 KB
J. Kasińska
Preliminary communication
 
Dynamic characteristics of automotive steel sheets (str.753-756) englishpdf 355 KB
M. Mihaliková, A. Lišková
Preliminary communication
 
Influence of selected rare earth metals on structural characteristics of 42CrMo4 steel (str.757-760) englishpdf 346 KB
J. Drápala, S. Brožová, I. Szurman, K. Konečná, G. Kostiuková, J. Vontorová, P. Jonšta, K. Sobotková
Preliminary communication
 
Advanced procedure for fabrication of substructure in dentistry (str.761-764) englishpdf 219 KB
I. Matin, M. Hadžistević, Đ. Vukelić, B. Trifković, M. Potran, T. Brajlih, I. Drstvenšek
Preliminary communication
 
Factors influencing the requirements fulfilment in the zinc coating processes (str.765-768) englishpdf 175 KB
T. Karkoszka
Preliminary communication
 
Detection of adherence imperfections at the inteface of substrate-coating layer by using infrared thermography (str.769-771) englishpdf 258 KB
A. C. Murariu, S. Crâsteţi, I. Samardzic
Preliminary communication
 
The analysis of influence the parameters of rolling process in three high skew rolling mill of AZ31 magnesium alloy bars on temperature distribution (str.772-774) englishpdf 236 KB
A. Gryc, T. Bajor, H. Dyja
Preliminary communication
 
Initial porosity impact on equal channel angular pressing (ECAP) of Ti–6Al–4V powder material (str.775-778) englishpdf 186 KB
V. A. Andreyachshenko, M. K. Ibatov, D. A. Issagulova
Preliminary communication
 
Stochastic optimization of laboratory test workflow at metallurgical testing centers (str.779-782) englishpdf 185 KB
F. Tošenovský, D. Vykydal, P. Klaput, P. Halfarová
Preliminary communication
 
Measuring the metallurgical supply chain resilience using fuzzy analytic network process (str.783-786) englishpdf 228 KB
P. Wicher, F. Zapletal, R. Lenort, D. Staš
Preliminary communication
 
Method of silicon filter refining from harmful impurities (str.787-789) englishpdf 191 KB
A. D. Mekhtiyev, Zh. D. Zholdubayeva, B. D. Issin, E. G. Ogoltsova, A. V. Yurchenko, K. D. Issin
Preliminary communication
 
The use of the balanced scorecard in evaluating the results of the innovations implemented in metallurgical companies (str.790-792) englishpdf 187 KB
L. Blacha, J. Brzóska
Preliminary communication
 
Gass presure sintered Si3N4 – MgSiN2 composites (str.793-795) englishpdf 198 KB
V. Pečínková, Z. Lenčéš, Z. Jonšta
Preliminary communication
 
Synthesis and characterization hollow spherical La0.7Sr0.2Ca0.1Co0.9Fe0.1O3–δ (LSCCT) for cathode of solid oxide fuel cell (SOFC) (str.796-798) englishpdf 217 KB
H. H. Yu, X. Li, Z. G. Yuan
Preliminary communication
 
Analysis of physical factors on chosen properties of anodic alumina oxide (AAO) layers and environment (str.799-802) englishpdf 198 KB
M. Gombár, J. Kmec, M. Badida, L. Sobotová, A. Vagaská, A. Badidová
Preliminary communication
 
Evaluating the possibilities of obtaining initial concentrates of rare earth elements (REEs) from fly ashes (str.803-806) englishpdf 164 KB
J. Całus Moszko, B. Białecka, M. Cempa-Balewicz, H. Świnder
Preliminary communication
 
Steel mill products analysis using qualities methods (str.807-810) englishpdf 169 KB
B. Gajdzik, J. Sitko
Preliminary communication
 
Application of risk analysis and quality control methods for improvement of lead molding process (str.811-814) englishpdf 300 KB
H. Gołaś, A. Mazur, B. Mrugalska
Preliminary communication
 
Optimization of casting defects analysis with supply chain in cast iron foundry process (str.815-817) englishpdf 98 KB
C. Narayanaswamy, K. Natarajan
Preliminary communication
 
Material and energy flow analysis (MEFA) – first step in eco-innovation approach to assessment of steel production (str.818-820) englishpdf 217 KB
J. Korol, M. Kruczek, M. Pichlak
Preliminary communication
 
Application of dominance-based rough set approach (DRSA) for quality prediction in a casting process (str.821-824) englishpdf 170 KB
A. Kujawinska, M. Rogalewicz, M. Piłacińska, A. Kochański, A. Hamrol, M. Diering
Preliminary communication
 
A thermal study of pipes with outer transverse fins (str.825-828) englishpdf 236 KB
S. Gil, J. Ochman, W. Bialik
Preliminary communication
 
Finite element simulation (FES) of the fullering in device with movable elements (str.829-831) englishpdf 120 KB
V. A. Andreyachshenko
Preliminary communication
 
Flotation of ores and waste waters (str.832-834) englishpdf 136 KB
R. Radić, Ž. Milošević, S. Jurić, S. Čudić
Review article
 
Advanced forming technology (str.835-838) englishpdf 213 KB
J. Kliber
Review article
 
Modified polysaccharides as alternative binders for foundry industry (str.839-842) englishpdf 127 KB
K. Kaczmarska, B. Grabowska, D. Drożyński, A. Bobrowski, Ž. Kurleto, Ł. Szymański
Review article
 
Integration of quality, environment and safety management systems in a foundry (str.843-845) englishpdf 120 KB
J. Łuczak, R. Wolniak
Review article
 
Sustainable cost reduction by lean management in metallurgical processes (str.846-848) englishpdf 108 KB
A. V. Todorut, L. Paliu-Popa, V. S. Tselentis, D. Cirnu
Review article
 
Influence of process parameters on the properties of austempered ductile iron (ADI) examined with the use of data mining methods (str.849-851) englishpdf 163 KB
D. Wilk-Kołodziejczyk, B. Mrzygłód, K. Regulski, I. Olejarczyk-Wożeńska, K. Jaśkowiec
Review article
 
Investigating occupational diseases in the metallurgical industry (str.852-854) englishpdf 166 KB
L. I. Cioca, L. Ivascu
Review article
 
Significance of technological entrepreneurship and creativity in metallurgical enterprises (str.855-858) englishpdf 114 KB
J. Machnik-Słomka, P. Kordel
Review article
 
Interdependence between iron ore production and maritime transport (str.859-861) englishpdf 119 KB
A. V. Todorut, L. Paliu-Popa, D. Cirnu
Review article
 
13th International Symposium of Croatian Metallurgical Society »Materials and Metallurgy« - SHMD `2018, Croatia, Šibenik, June, 24 – 28, 2018 - First Circular – Call for Papers (str.862-864) englishpdf 118 KB
Ilija Mamuzić
Other
 
Visits: 46.731 *